I have done one short movie on my Race fairing.
https://www.youtube.com/watch?v=o7vX70DZES0
I paint it nearly like the orginal. its not mint !
It was fun to paint but not easy!
//Kesson
My 2 new bikes!
-
- Newbie
- Posts: 19
- Joined: Tue Aug 23, 2016 4:48 pm
- Location: SWEDEN
Re: My 2 new bikes!
RS 250 -02. R6-01. 2*KR1S-90. Rotax max DD2 -16.
-
- Newbie
- Posts: 19
- Joined: Tue Aug 23, 2016 4:48 pm
- Location: SWEDEN
Re: My 2 new bikes!
Hi !
I have get al fairing monted on my kr1s today so i was going to take it for a run, its could be fun i think.But when i was try to start it up i broke the kickstarteraxle
Is the kickstarter axle some weck pointe att the kr1s?
Sorry for my spelling. Best regards kesson.
I have get al fairing monted on my kr1s today so i was going to take it for a run, its could be fun i think.But when i was try to start it up i broke the kickstarteraxle
Is the kickstarter axle some weck pointe att the kr1s?
Sorry for my spelling. Best regards kesson.
RS 250 -02. R6-01. 2*KR1S-90. Rotax max DD2 -16.
-
- Heavy Smoker
- Posts: 126
- Joined: Sat Mar 26, 2011 12:18 am
- Location: Rep of Ireland
Re: My 2 new bikes!
The revs are not dropping quick enough on that bike..kesson wrote: ↑Tue Nov 08, 2016 10:30 pm Thanks for all nice words.
I love this bikes and the sound of the engine, i have load up one litle
movie on youtube.
https://www.youtube.com/watch?v=TiJC_oSO3w0
I think the engine are going to leane at the lower rpm it dont answer
direct on the throtle.I going to take a look at the jet in the carburater
now when the winter are on the way to sweden.
Best regards kesson.
I"ll take the wine,you can have the bread.
- Binetta Steve
- Oil Injector
- Posts: 949
- Joined: Sat Nov 10, 2012 6:13 pm
- Location: North Wales
Re: My 2 new bikes!
Sounds like air screw issue, see Bernies advice here
Post by 500bernie » Sun May 14, 2017 8:30 am
Hi the revs hanging is down to your air screw settings, the bike is too lean. Your air screws need turning in a little more. Loads of posts here on the forum about this topic, the manual setting of 1 1/2 turns out is way too lean, start at 3/4 turns out (you will see some posts where they are only 1/4 turn out).
Good luck.
Bernie
Post by 500bernie » Sun May 14, 2017 8:30 am
Hi the revs hanging is down to your air screw settings, the bike is too lean. Your air screws need turning in a little more. Loads of posts here on the forum about this topic, the manual setting of 1 1/2 turns out is way too lean, start at 3/4 turns out (you will see some posts where they are only 1/4 turn out).
Good luck.
Bernie
-
- Newbie
- Posts: 19
- Joined: Tue Aug 23, 2016 4:48 pm
- Location: SWEDEN
Re: My 2 new bikes!
Hi !
I havent fixed the bike, i stamp of the startpedal/kickstarter ! I have one kit jetings and needled for the carburates that i going to mount when i have vacassion this month. Then i going to set the air screw as Bernie advise.
Best regards kesson (sorry for my speling)
I havent fixed the bike, i stamp of the startpedal/kickstarter ! I have one kit jetings and needled for the carburates that i going to mount when i have vacassion this month. Then i going to set the air screw as Bernie advise.
Best regards kesson (sorry for my speling)
RS 250 -02. R6-01. 2*KR1S-90. Rotax max DD2 -16.
-
- Newbie
- Posts: 5
- Joined: Thu Jul 20, 2017 1:30 pm
- Location: Tuen Mun, Hongkong