Project KR1SS - So far

[500bernie]

Way to go Gary. =D> =D> =D>

Dave Wood's........ 66bhp
Gibson's............... 67.1bhp

What's next?

Krazy Kats............ 70bhp

[martin]

krazy kats dyno 70bhp

krazy kats dyno reads very optimistic

[500bernie]

[gary]

Hi, had a great day at the Gibson Dyno day. Brilliant weather & lots of interesting bikes on show. Really pleased with the results I got

[500bernie]

Great photos Gary, did you video your run?

[headcoats]

Is a pretty outstanding result

My highly tweaked 350 YPVS motor only did 67.91bhp LOL

[500bernie]

Is a pretty outstanding result

My highly tweaked 350 YPVS motor only did 67.91bhp LOL

You should have taken the Triumph Martin.

[headcoats]

Sorry meant to say that was a dyno run on my local dyno centre here in Sunny Cradley Heath

Trumpet ain't running well ,think I have an air leak so getting some new carb rubbers and manifold 0 rings just to eliminate that

[martin]

yes martin but is it a very optimistic dyno

[500bernie]

I am optimistic that this will work [-o<



The beast delivering 67.1 BHP (ARW) =D> =D> =D> =D> =D> =D> =D>

[375]

Didn't know you was there Bernie, i got there at about 2pm had i known you and Martin where going i would have tried to have got there a bit sooner.

[500bernie]

Didn't know you was there Bernie, i got there at about 2pm had i known you and Martin where going i would have tried to have got there a bit sooner.

No, only Gary and Martin went to get Garys bike on the dyno.
My only contribution is to half the size of the video file so it could be uploaded, I wish I had been there

[martin]

think you mixed the premix a tad rich gary.
maybe take the kr to krazy kats and get the zeeltronic ignition dialled in. could be 68 -69bhp
am sure it will give one or two more horses, but as I have said to you ,be carefull
with the state of tune on the engine. tick tock tick tock

video is great. it actually sounds like it has loads of power.

but then again. I am very optimistic

on a sensible note, I feel its a great shame that some regular members have doubted and knocked this rebuild as I am more than happy
to tell people the two to three things that made the difference to the bhp figures.

[JanBros]

optimistic

is this going to be a running joke ?

on a sensible note, I feel its a great shame that some regular members have doubted and knocked this rebuild as I am more than happy
to tell people the two to three things that made the difference to the bhp figures.

no one doubted or knocked this rebuild, it was just a simple discussion about dyno's.

watch this space
I have just bought a set of new jolly moto pipes.
and a few more mods.
I have,nt been on this forum for a while as there has been a lot of negative remarks
of garys 300cc kr1s that I built. [you all know the bike I mean, the most powerfull kr1s on the forum and prob the country. ]
I am now building a true 250cc kr1 , not kr1s. and lets see if I break 60bhp.

nothing pesonal against you Martin, and welcome back, but it's posts like this one that sends shivers down my spine. you make it sound like you are the one and only, THE KR1-specialist. but there are lot's on here and there is no reason at all why you should be better than the next.

[tescr500]

Hi Gary bike looks fantastic, dyno readings were great, bit of a sore point as I have read ooops handbags Anyway that said. Could anyone tell me if they have heard anything about Gary Teague Tuning, its in Eastleigh which is only half hr from where I live, so convenient for me. Or anywhere close ish to Andover Hampshire. I think mine will need setting up, (purchased off Martin) its tuned barrels, head and its got 29.5 bore carbs on it, I have a good idea about setting it up, know the basics but would like to have it set up properly and dyno for sure. I can rebuild and repair no sweat, but tuning I must say I am a bit green on this front. So any advice free support, free services I'm easy more than welcome
Just the last thing where can I find this dam dyno video cheers Wayne.